COLD AIR INTAKE FOR 17-19 FORD POWERSTROKE F250/350 6.7L -RAW HSP DIESEL

The HSP 1719 Powerstroke intake has been engineered to capture incoming airflow into the engine bay more efficiently than stock while maintaining factory MAF calibration. This intake utilizes the most direct path for airflow into the engine. On the dyno, this intake picked up 12.5 horsepower over stock and shifted peak torque to 500 RPM sooner in the power band.

This intake not only improves engine performance but also produces more turbo noise than the stock intake. This product also features a newly designed HSP air filter with more filter area than previous generations of HSP filters.

What Does the HSP Cold Air Intake Do Differently?

It locates the intake in front of the battery in the engine bay, closer to the incoming ambient air than stock. The single-piece mandrel-bent 4.5 inch intake pipe has less restriction and fewer bends than the factory plastic intake. The sheet metal heat shield box captures the filter and deflects engine bay heat, helping to prevent heat soaking in the intake system.

What Comes with the HSP Cold Air Intake?

• 1x 17-19 Ford Cold Air Intake (HSP-IN-153-3)
• 1x 17-19 Ford Heatshield Box (HSP-IN-747)
• 1x 17-19 Ford Battery Tray (HSP-IN-696)
• 1x 17-19 Ford Battery Tray Bracket (HSP-IN-695)
• 1x HSP-IN-744-2 17-19 Ford Heatshield Box Lid (HSP-IN-744-2)
• 1x 17-19 Ford Battery Tie Down (HSP-IN-693)
• 1x MEGA 4.5 inch Filter Angled ( RFB-514-RFAB )
• 1x Small HSP Logo - No Holes (Flat) (RFB-752-F-1-RFAB)
• 1x Two sided tape (RFB-900-RFAB)
• 2x Ford 17-19 Battery Extension Cable (HSP-IN-1024)
• 2x M8 Flange Bolt (RFB-1022-RFAB)
• 6x M6 Flange Bolt (RFB-1023-RFAB)
• 2x M6 Nylon Lock Nut (RFB-916-RFAB)
• 6x Heat Deflector Sheathing Roll(RFB-1026-RFAB)
• 6x Heat Shrink Roll (RFB-1027-RFAB)
• 6x Heat Shrink Roll(RFB-1027-RFAB)
• 4x Black Nylon Push-Type Retainer (RFB-095-RFAB)
• 2x 4.5 inch T-Bolt Clamp (RFB-435-RFAB)
• 1x 4.5 inch 55 deg boot (RFB-858-RFAB)
• 4x 1/8 inch Aluminum Rivet (RFB-098-RFAB)
• 1x LB7-LML Heatshield Box Lid Backer Plate (RFB-746-BP-RFAB)
• 2x M4x.7x10mm Bolt (RFB-901-RFAB)

What Does This Fit?

• Ford 6.7: 2017-2019

Special Note:

This only fits the 2017-2019 6.7L Powerstroke engine. This is due to small changes that we're made in the engine bay. Please be sure you are ordering for the correct year truck.

Disclaimer:

Dyno data was collected on a completely stock truck with factory calibration in a controlled environment. Results may vary based on engine modifications and ambient conditions. For best results, pair with HSP intercooler piping.

Overview:

• Increased performance
• Maximizes factory part and emissions system
• High flowing cold air intake
• Diameter hot and cold side tubes
• High strength 5-layer silicone boots
• Powder coat options for a clean look under the hood

HSP No BS Limited Lifetime Warranty

At HSP we believe in our products and we stand firmly behind every single one that leaves our facility. For years we have taken care of almost everything and anything that our customers had issues with, but we didn't have a set in stone warranty. We have always gone above and beyond for our customers which set us apart from the rest. We will continue that same standard, but now we are taking things to the next level.